Sizing for the Simplus Mask
Sizing for the Simplus Mask
How does the sizing on the Simplus compare to other masks. I'd use a large in the Mirage Quattro and the Quattro FX, would this be the same for the Simplus? I can never get those sizing charts to print out right.
_________________
Machine: ResMed AirCurve 10 ASV Machine with Heated Humidifier |
Mask: Evora Full Face Mask - Fitpack |
Additional Comments: AirCurve 10 ASV, Oscar V1.0.1-r-1 |
US Navy Retired 1973,AirCurve 10 ASV, Mode: ASV Auto, Min EPAP: 7.2, Max EPAP: 15.0, Min PS:4.0, Max PS: 15.0, Mask ResMed Airtouch F20, Backup: (2) AirCurve 10 ASV
- Bama Rambler
- Posts: 189
- Joined: Wed Feb 19, 2014 10:25 am
Re: Sizing for the Simplus Mask
I use a medium in the MQ and the FX and I'm a medium in the Simplus The DW is a small in the MQ as well as the Simplus, so I'd venture that the Simplus is sized the same as the MQ & FX.
- Sir NoddinOff
- Posts: 4190
- Joined: Mon May 14, 2012 5:30 pm
- Location: California
Re: Sizing for the Simplus Mask
Try this but make sure you print at 100%:
http://www.cpapxchange.com/cpap-masks-b ... -gauge.pdf
Hit the printer Icon on the top right > hit properties button > hit effects tab (make sure it sez 100% half way down, if it doesn't then enter 100%) > hit OK till it prints. Usually there's a inch scale also printed on the page but F&P just give you a little inch square on the right side. Check that with a ruler. You may have to select 'landscape' if it tried to print it sideways (ie. off the page). That's on the 'finishing' tab.
http://www.cpapxchange.com/cpap-masks-b ... -gauge.pdf
Hit the printer Icon on the top right > hit properties button > hit effects tab (make sure it sez 100% half way down, if it doesn't then enter 100%) > hit OK till it prints. Usually there's a inch scale also printed on the page but F&P just give you a little inch square on the right side. Check that with a ruler. You may have to select 'landscape' if it tried to print it sideways (ie. off the page). That's on the 'finishing' tab.
_________________
Mask: AirFit™ F10 Full Face Mask with Headgear |
Additional Comments: Sleepyhead software v.0.9.8.1 Open GL and Encore Pro v2.2. |
I like my ResMed AirFit F10 FFM - reasonably low leaks for my ASV therapy. I'm currently using a PR S1 AutoSV 960P Advanced. I also keep a ResMed S9 Adapt as backup. I use a heated Hibernite hose. Still rockin' with Win 7 by using GWX to stop Win 10.
Re: Sizing for the Simplus Mask
I use a medium in the Mirage Quattro FFM, but a large in the Simplus. In my experience, the Simplus runs a little small, but not by much. If you're a large in the Quattro, you're definitely a large in the Simplus.
_________________
Machine: AirCurve™ 10 VAuto BiLevel Machine with HumidAir™ Heated Humidifier |
Mask: AirFit™ P10 Nasal Pillow CPAP Mask with Headgear |
Additional Comments: BreatheWear Halo Chinstrap |
Re: Sizing for the Simplus Mask
I was a large in Quattro and am now a large in Simplus. Only my nose feels much better now and it doesn't leak as much on my side.
Don
Don
_________________
Mask: Simplus Full Face CPAP Mask with Headgear |
Additional Comments: I only look at little screen on machine, let doc analyse details. Now machine set up for me. |
Using Tapatalk